Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
|
25%
50%
0%
25%
0%
|
 Rating: Review Date: 01/06/10 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:Not enought thread
Pros:Nice looking |
|
Rating: Review Date: 11/10/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:had 1 leakage in the 1st 24hrs on 1 using the standard manual max + 1/2-1/4 lock turn. this didn't re-occur.
Pros:clean look, well coated, so simple to install you'll ask your kid to do it. Comment:
Strangely moved to another device in the watercooling chain and the problem went away, eventually opted for compression fittings as a very personal choice. they are to be recommended only for the price and the fact that they perform really well under the right circumstances. Consider the compression fittings if it fits your setup plan. they are really cheap but are not a complete solution on their own. |
|
Rating: Review Date: 10/24/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:None
Pros:Good price, quality construction, Bitspower reputation. Comment:
These did the job well, look good, no leaks. Used these on my heatkiller block. What more can you ask for? |
|
Rating: Review Date: 10/23/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:None
Pros:Long fitting for tubeSturdy Comment:
These are great barbs! It's no some fancy barb but it does the job and does it well. I tried some other barbs, and found these ones to be the most easy to work with. I would have chose compression fittings but they are too expensive. |
|
Rating: Review Date: 04/15/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:short threads
Pros:Great pricewell made Comment:
great barbs which look pretty. the threading is a little short but its not a big deal. well made and would buy again |
|
Rating: Review Date: 03/05/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:-None
Pros:-1/2" ID-G1/4-High quality Comment:
I bough 6 sets of these for my watercooling loop, and they work great. They have great water flow and very high quality. I have 7/16" tubing on these and its a very good fit and seal is awesome :) This review was modfied by poster @ 03-05-09 01:46 PM |
|
Rating: Review Date: 03/02/09 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:Short threads on one side.
Pros:Great build quality. Comment:
Bought 2 sets for my watercooling setup and they work well. They do what they are supposed to! Only complait is that the threading on one side is a bit short but it still holds strong. |
|
Rating: Review Date: 06/02/08 |
Bitspower BP-WTP-C01 1/2IN G1/4 High Flow Barb Fittings
Cons:short threading.
Pros:Great quality Comment:
Some really great fittings here with excellent build quality and craftsmanship. Only problem is the really short threading that i think they should of made a little longer. |
Bought these for water cooling setup.Put it all together and one leaked.Couldn't get it to stop.There is just not enought thread on them.Had to use an old set and everything was fine.