Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
|
63%
38%
0%
0%
0%
|
 Rating: Review Date: 04/24/13 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:pricematch required
Pros:great Swiftech fit and finish |
|
Rating: Review Date: 11/23/11 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:none
Pros:very usefulllooks good Comment:
i picked this up to use as drain port for my loop. This is a very nice drainport. Not to fancy but does the job well and is good quality. The installation is very simple |
|
Rating: Review Date: 11/01/11 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:Expensive
Pros:Excellent fill port, drain port Comment:
Great fill port or drain port. Expesive for what it is, 1/2 the price would be better. No negatives on the product itself. |
|
Rating: Review Date: 06/20/11 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:price
Pros:looks goodeasy to use Comment:
it is kind of expensive for what it is i needed one anyway |
|
Rating: Review Date: 10/30/10 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:
None
Pros: +quality+price when pm Comment:
This is perfect for your filldrain port its Cheap and get in the tube pretty tight make the thing way way simpler |
|
Rating: Review Date: 09/26/10 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:
none
Pros: very usefull Comment:
use either a large flat headed screw driver that will fit snugly into the slot of the cap, or a coin to tighten and loosen the cap, or suffer some minor cosmetic damage to the cap. |
|
Rating: Review Date: 07/30/10 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:
a rubber ring around the base would be a nice addition
Pros: Simple to installGreat chrome finish Comment:
This is a very nice fillport. Not to fancy but does the job well and is good quality. The installation is very simple, you just need a 5/8 hole and screw the bottom nut and voila! |
|
Rating: Review Date: 08/02/09 |
Swiftech Water Cooling Fillport W/ 1/2" High Flow Barb Fitting - Mounts Into A 5/8IN Hole
Cons:None really
Pros:Easy to install, its very simple! Comment:
Great little addition to a water cooling setup to provide inlet/outlet for filling or draining (I have two in water loop, one to fill from and one to drain from).I would suggest using either a large flat headed screw driver that will fit snugly into the slot of the cap, or a coin to tighten and loosen the cap, or suffer some minor cosmetic damage to the cap.I used a stepper bit to drill the hole for this. I ended up drilled a 3/4 inch hole to allow my 1/2inch ID 3/4 OD tubing to slide through the hole. 5/8 hole did not even seem large enough for the threads anyways. |
eay to install fillport can be drain or passthrough too